Firmness is not support: what actually matters in a mattress
Firmness labels are not standardised and two minutes on your back proves nothing. Body weight, sleeping position and a proper trial decide whether a mattress suits you.
The usual mattress test goes like this. You sit on the edge, bounce once, lie flat on your back in your coat with your shoes hanging off the end, stare at the ceiling for forty seconds while a salesperson stands nearby, and declare it fine. Then you go home and sleep on your side for the next eight years.
A mattress is hard to buy well because the thing you are judging only shows itself over hours, and the words on the label mean less than they appear to. A few principles cut through most of the confusion.
Support and firmness are different things
Support is whether your spine stays in roughly the line it has when you stand well. Firmness is how the surface feels when you press into it. A mattress can be soft on top and supportive underneath, or hard and unsupportive, as anyone who has slept on a floor can confirm: the hips and shoulders have nowhere to go, so the waist hangs unsupported between them.
Firmness words are also not standardised. One maker's medium is another's firm, and the same mattress feels firmer to a light person than to a heavy one, because a lighter body does not sink far enough to engage the deeper layers. The old advice that a hard bed is good for a bad back has not held up well. For most people something in the medium to medium-firm range, adjusted for build, is the safer starting point.
Start from how you sleep and what you weigh
- Side sleepers need the shoulder and hip to sink in so the spine stays level. That usually means a softer comfort layer. Numb arms and sore shoulders are the sign of a surface that is too hard.
- Back sleepers need the lower back filled in without the hips dropping. Medium to medium-firm suits most.
- Front sleepers need the firmest surface of the three, because a soft one lets the pelvis sink and arches the lower back.
- Heavier bodies compress a mattress further, so they generally need a firmer, deeper model to get the same feel a lighter person gets from a softer one.
- Couples with very different builds should look at split tension options or two single mattresses on one base before compromising on something that suits neither.
What is inside, in plain terms
| Open coil springs | One linked spring unit. Cheap and bouncy, transfers movement across the bed, tends to dip sooner. Reasonable for a guest room |
|---|---|
| Pocket springs | Each spring in its own fabric sleeve, moving independently. Better contouring and less partner disturbance. Breathes well |
| Memory foam | Moulds slowly to the body and absorbs movement. Can sleep warm, and some people dislike the feeling of being held in place |
| Latex | Springy, resilient and durable, cooler than memory foam. Heavy to move and usually costly |
| Hybrid | Pocket springs under a foam or latex comfort layer. A middle course, and quality varies widely with the thickness of each layer |
Spring counts are quoted as if more were always better. Past a sensible number the gains are small, and counts are sometimes inflated by stacking layers of tiny springs. The gauge of the wire, the quality of the comfort layers and the density of any foam matter as much. Foam density is worth asking about directly, because low-density foam is the usual reason a mattress develops a body-shaped hollow within a couple of years.
How to test one properly
- Take off your coat and shoes, and bring your own pillow if you can bear to. Pillow height changes everything about how your neck sits.
- Lie in the position you actually fall asleep in and stay there for ten to fifteen minutes. The first minute tells you about the surface, the tenth about the support.
- On your back, slide a hand under the small of your back. A big gap means too firm, a hand you can hardly get in means too soft.
- On your side, have someone check that your spine looks level from neck to tailbone, without the hip hiking up or sagging.
- If you share the bed, test together. Have one person turn over and see how much the other feels, and both lie near the edges to check it does not slope away.
Even a good shop test is a short one, so the return terms matter more than almost any feature. Many sellers offer a home trial of some weeks. Read what it requires: some insist you keep the mattress for a minimum period first, which is reasonable because a body takes a few weeks to adjust, and some require a protector to have been used. A stained mattress is rarely returnable.
The base, the size and the old one
A new mattress on a tired base inherits its faults. Check slats for bowing and for gaps: wide gaps let foam and pocket springs push through and can void a guarantee, and many makers specify a maximum spacing of a few centimetres. Sprung slats soften the feel, a solid platform firms it up. Buy the largest size the room takes comfortably, since two adults in a standard double each get less width than a child has in a cot.
As for when to replace, age is a rough guide and the evidence is better. A visible dip where you lie, springs you can feel, rolling toward the middle, or regularly waking stiff and sleeping better in other beds all say the same thing. Rotating the mattress head to foot every few months in its first years, and using a washable protector from the first night, will put that day off further than anything else.